Code:
BOOTROM Load Burn Sheet V1.0
Proposed: MBB Maintenance Support Team Date: 2013-04-20
Audit: Date:
Approved: Date:
Huawei Technologies Co., Ltd
Huawei Technologies Co., Ltd.
All rights reserved
All rights reserved
Revision record
Date Revisions Revision Reason Revision Section Modification Description Author
2013-04-20 V1.0 MBB Maintenance Support Team
The company is located in:
The company is located in:
The company is located in:
The company is located in:
The company is located in:
The company is located in:
The company is located in:
The company is located in:
The company is located in:
The company is located in:
The company is located in:
The company is located in:
table of Contents
Chapter 1 Scope 4
Chapter 2 BOOTROM loading burn film guide 5
2.1 Environmental Preparation 5
2.2 loading burn environment to build 6
2.2.1 Bootrom burn tool download and installation 6
2.2.2 install the driver 8
2.3 burning piece guidance 8
2.3.1 BOOTROM load 8
Chapter 1 Scope of application
BOOTROM Loaded Burning Chip MBB products mainly apply to Barron V3, V7 and above platform data card, the specific models are as follows:
Platform standard models
Barron V3 WCDMA Data Cards E303s, E303Fs, E303Gs, E303Ds, E303Ms, E303Cs, K3773, E355s, GD03W, E8131s, E8131s, E3121s, E3131As, E3131Gs, E3131Cs, K4305, K4201, E359s, E357s, E352As, E3131s, HiLink E303s , HiLink E353Ws, HiLink E3231Ws, HiLink E3251s, HiLink E3256s, HiLink E3256Ws, E8238Ws, E8258Ws, E8259Ws
Baron V7 LTE data card E3276s, E3272s, E8278s, 203HW, GL08D
E5 E5776s, 102HW, E5331s, E5756s, HW-02E, GL06P, E5332s, HW-01F, E5573s, E5577s, E5577Cs
Chapter 2 BOOTROM Loading Slices Instructions
2.1 Environmental Preparation
Name Quantity Code
Hardware PC (Universal) 1PCS
USB adapter cable 1PCS
Metal tweezers 1PCS
Software (downloadable from the support website or via the Compartner platform) Production driver 1PCS Product Line WinDriver (subject to the latest version)
BOOTROM loading tool 1PCS BootRomDownloadTool
WCDMA standard (V3 platform): 05010LJP
LTE standard (V7 platform): 05011AKY
XXXX burn film 1PCS for the specific model
Description:
USB cable: easy to operate.
Tweezers: Used to short connect BOOT_SEL and GND, can be replaced by other tools.
support Website: http://support.huaweidevice.com
2.2 loading flaky environment to build
2.2.1 Bootrom burn tool download and installation
1, open the service Support site, enter Compartner (if you have already installed Compartner platform, skip to step 3).
Support website: http://support.huaweidevice.com
2, download, and follow the prompts to install Compartner;
3, use the account and password to log on the Compartner platform, click "Select Device", enter the name of the model to be upgraded, double-click the selected model.
4, point to open "loading tools", double-click the tool to download and install (different models may correspond to different tool encoding).
5, after installing the Bootrom tool, the tool will automatically open, and then select the software configuration.
BootRom: Select usbloader.bin in the burn software
Firmware: Choose burn software.
2.2.2 install the driver
In the Support website, enter Product Line WinDriver.
2, download the latest version of this driver to install.
a) Double-click DriverSetup, driver installation. Double-click, the PC interface will not have any pop-up, only the mouse will turn for a while. After installation, will pop up an Install.txt in the same folder. Open Install.txt, which can see the driver's installation status.
b) Double-click DriverUninstall, driver uninstall. Uninstall the same way and installation.
c) Note: When installing and uninstalling this driver, never connect the data card to the PC. Need to install or uninstall the driver is complete, and then connect the data card and PC.
2.3 burning piece guide
2.3.1 BOOTROM loading
1, open the burn tool, configure the burn software, and then click Next;
2, double-click "Expectant count" can enter the need to load the number (support 1-8).
3, click "Scan & Upgrade".
4. Find the loading point of the board (BOOT_SEL, it will be indicated in the general maintenance manual). Short the ground to the ground with tweezers or other tools. Connect the data card to the computer through the USB extension cable until the port below appears Release the tweezers.
5, loading
6, loaded successfully.
7, after loading burn piece, carry on CBT, upgrade, write number, write custom and other steps.translated version ng bootrom document galing sa general firmware na nauna kong nakuha
so, possible talaga na pwedeng walang battery kapag magiinstall ng firmware
