MF286RA openwrt.

Frwa · Jul 9, 2022

malows08 said:
Thanks sa info sir try ko maghanap sa shopee.pero sana may mag up ng video para masundan.thanks

Pero sabi ng mga idol natin,baka magbenta nalang sila ng zte na openwrt na agad.2400 free shipping na.hintay hintay nalang

Sana nga po may video sana para masundan

PHC-Shin · Jul 9, 2022

lorenda · Jul 9, 2022

up....

dwakjbnd · Jul 9, 2022

sUFF3R said:
Sanay may makapag tip san yung tx rx gnd sa serial sa mf286ra

check mo ung malapit sa lte modem. may 4 pads dun. mataas chance na un ang uart pads.

sUFF3R · Jul 9, 2022

dwakjbnd said:
check mo ung malapit sa lte modem. may 4 pads dun. mataas chance na un ang uart pads.

problem ko po boss is di matukoy san yung tx rx gnd kasi sira tester

v2ray · Jul 10, 2022

nagana pa kaya ang telephone functionality pag naka openwrt?

D34DS3C · Jul 10, 2022

sUFF3R said:
problem ko po boss is di matukoy san yung tx rx gnd kasi sira tester

eto lods baka makatulong sayo

mayrence · Jul 10, 2022

Tambay muna ehhehe

jeromelaliagg said:
Ang itry mo yung dual wan nya, isaksak mo sa WAN/LAN1 ang isa pang internet source tapos check mo internet speed, matic mag cocombine or load balance ang LTE/WAN nyan, tapos hugutin mo ang WAN/LAN1, stable parin ang ping naka failover narin ang config nyan. Kung sa LTE mo naman susubukan ang failover try mo iconnect WAN/LAN1 tapos mag change bands ka, goods parin ang ping.

Naka preconfig na ang Dual WAN, Fail Over at Load Balance nyan.

Ito kaylangan ko hehehee!!

v2ray · Jul 10, 2022

sUFF3R said:
problem ko po boss is di matukoy san yung tx rx gnd kasi sira tester

haha bili na bago tester lodi

unel · Jul 10, 2022

dwakjbnd said:
wala pang wiki entry para sa mf286r/a pero andito instructions na di need ng tftp

You do not have permission to view the full content of this post. Log in or register now.
gumagana rin lte. may exploit para di na need ng serial

Na try mo na ,boss?

dwakjbnd · Jul 10, 2022

unel said:
Na try mo na ,boss?

1. connect serial
2. interrupt uboot

pag naka uboot ka na

Code:

STEP 3: Booting initramfs image:

Method 1: using serial console (RECOMMENDED):
- Have TFTP server running, exposing the OpenWrt initramfs image, and
  set your computer's IP address as 192.168.0.22. This is the default
  expected by U-boot. You may wish to change that, and alter later
  commands accordingly.
- Connect the serial console if you haven't done so already,
- Interrupt boot sequence by pressing any key in U-boot when prompted
- Use the following commands to boot OpenWrt initramfs through TFTP:

  setenv serverip 192.168.0.22
  setenv ipaddr 192.168.0.1
  tftpboot 0x81000000 openwrt-ath79-nand-zte_mf286r-initramfs-kernel.bin
  bootm 0x81000000

  (Replace server IP and router IP as needed). There is no  emergency
  TFTP boot sequence triggered by buttons, contrary to MF283+.
- When OpenWrt initramfs finishes booting, proceed to actual
  installation.

tapos pwede mo na iscp ung firmware

Code:

STEP 4: Actual installation:
- Set your computer IP to 192.168.1.22/24
- scp the sysupgrade image to the device:

  scp openwrt-ath79-nand-zte_mf286r-squashfs-sysupgrade.bin \
  root@192.168.1.1:/tmp/

- ssh into the device and execute sysupgrade:

  sysupgrade -n /tmp/openwrt-ath79-nand-zte_mf286r-squashfs-sysupgrade.bin

- Wait for router to reboot to full OpenWrt.

para sa bandlocking - You do not have permission to view the full content of this post. Log in or register now.
pwede ka na maginstall ng mwan3 at iconfigure.
kayo na bahala sa unlock
AT+ZNCK="nckcode" via /dev/ttyACM0

I am nobody · Jul 10, 2022

dwakjbnd said:
may band 28 ang s12 ρrø and openwrt ang firmware ng s12 ρrø. iba lang libc na gamit kaya di ka directly makakainstall from openwrt repo unless install mo musl.

Oo ok narin, open naman telnet.

dwakjbnd · Jul 10, 2022

dwakjbnd said:

1. connect serial
2. interrupt uboot

pag naka uboot ka na

Code:

STEP 3: Booting initramfs image:

Method 1: using serial console (RECOMMENDED):
- Have TFTP server running, exposing the OpenWrt initramfs image, and
  set your computer's IP address as 192.168.0.22. This is the default
  expected by U-boot. You may wish to change that, and alter later
  commands accordingly.
- Connect the serial console if you haven't done so already,
- Interrupt boot sequence by pressing any key in U-boot when prompted
- Use the following commands to boot OpenWrt initramfs through TFTP:

  setenv serverip 192.168.0.22
  setenv ipaddr 192.168.0.1
  tftpboot 0x81000000 openwrt-ath79-nand-zte_mf286r-initramfs-kernel.bin
  bootm 0x81000000

  (Replace server IP and router IP as needed). There is no  emergency
  TFTP boot sequence triggered by buttons, contrary to MF283+.
- When OpenWrt initramfs finishes booting, proceed to actual
  installation.

tapos pwede mo na iscp ung firmware

Code:

STEP 4: Actual installation:
- Set your computer IP to 192.168.1.22/24
- scp the sysupgrade image to the device:

  scp openwrt-ath79-nand-zte_mf286r-squashfs-sysupgrade.bin \
  root@192.168.1.1:/tmp/

- ssh into the device and execute sysupgrade:

  sysupgrade -n /tmp/openwrt-ath79-nand-zte_mf286r-squashfs-sysupgrade.bin

- Wait for router to reboot to full OpenWrt.

para sa bandlocking - You do not have permission to view the full content of this post. Log in or register now.
pwede ka na maginstall ng mwan3 at iconfigure.
kayo na bahala sa unlock
AT+ZNCK="nckcode" via /dev/ttyACM0

in addition pala dito. pag nasa stock fw ka, pwede mo maaccess root shell ng lte module (pxa1826) using adb shell
kayo na bahala maghanap kung maunlock niyo via that. di naman importante sakin ung unlock.

sUFF3R · Jul 10, 2022

D34DS3C said:
View attachment 2022206
eto lods baka makatulong sayo

waw thanks boss mf286ra bato?

v2ray said:
haha bili na bago tester lodi

haha kakabili ko lang paps waiting pa ako madeliver, kakaorder ko lang shoppe haha

dwakjbnd said:

1. connect serial
2. interrupt uboot

pag naka uboot ka na

Code:

STEP 3: Booting initramfs image:

Method 1: using serial console (RECOMMENDED):
- Have TFTP server running, exposing the OpenWrt initramfs image, and
  set your computer's IP address as 192.168.0.22. This is the default
  expected by U-boot. You may wish to change that, and alter later
  commands accordingly.
- Connect the serial console if you haven't done so already,
- Interrupt boot sequence by pressing any key in U-boot when prompted
- Use the following commands to boot OpenWrt initramfs through TFTP:

  setenv serverip 192.168.0.22
  setenv ipaddr 192.168.0.1
  tftpboot 0x81000000 openwrt-ath79-nand-zte_mf286r-initramfs-kernel.bin
  bootm 0x81000000

  (Replace server IP and router IP as needed). There is no  emergency
  TFTP boot sequence triggered by buttons, contrary to MF283+.
- When OpenWrt initramfs finishes booting, proceed to actual
  installation.

tapos pwede mo na iscp ung firmware

Code:

STEP 4: Actual installation:
- Set your computer IP to 192.168.1.22/24
- scp the sysupgrade image to the device:

  scp openwrt-ath79-nand-zte_mf286r-squashfs-sysupgrade.bin \
  root@192.168.1.1:/tmp/

- ssh into the device and execute sysupgrade:

  sysupgrade -n /tmp/openwrt-ath79-nand-zte_mf286r-squashfs-sysupgrade.bin

- Wait for router to reboot to full OpenWrt.

para sa bandlocking - You do not have permission to view the full content of this post. Log in or register now.
pwede ka na maginstall ng mwan3 at iconfigure.
kayo na bahala sa unlock
AT+ZNCK="nckcode" via /dev/ttyACM0

thanks lodi try ko to

Frwa · Jul 10, 2022

dwakjbnd said:
in addition pala dito. pag nasa stock fw ka, pwede mo maaccess root shell ng lte module (pxa1826) using adb shell
kayo na bahala maghanap kung maunlock niyo via that. di naman importante sakin ung unlock.

Sir pwede pagawa ng video tutorial po.

dwakjbnd · Jul 10, 2022

Frwa said:
Sir pwede pagawa ng video tutorial po.

di ako nagamit ng windows so di rin applicable sa halos lahat ng users dito

sUFF3R · Jul 10, 2022

boss paano po ma interrupt uboot

dwakjbnd said:
di ako nagamit ng windows so di rin applicable sa halos lahat ng users dito

PHC-Shin · Jul 10, 2022

hello sino pwede help sakin newbie lang po ako sa open vpn sa modem

pano po ba ilagay yun config sa modem nag fafatal error po kasi e may babaguhin paba don ang ginawa ko po kasi is upload ko lang then click enable and start anyway ang modem kopo zte mf286ra openwrt

Screenshot_2022-07-10-22-08-43-11_40deb401b9ffe8e1df2f1cc5ba480b12.jpg

dwakjbnd · Jul 11, 2022

sUFF3R said:
boss paano po ma interrupt uboot

dapat nakaplug na uart mo. tapos ion mo ung router. lalabas dun un countdown. bago matapos press a key.

hushbona said:
hello sino pwede help sakin newbie lang po ako sa open vpn sa modem

pano po ba ilagay yun config sa modem nag fafatal error po kasi e may babaguhin paba don ang ginawa ko po kasi is upload ko lang then click enable and start anyway ang modem kopo zte mf286ra openwrt

View attachment 2023285

gamitin mo ung 22.03 rc instead of snapshot You do not have permission to view the full content of this post. Log in or register now.
panget gumamit ng snapshot pag di mo alam ginagawa mo.

PHC-Shin · Jul 11, 2022

dwakjbnd said:
dapat nakaplug na uart mo. tapos ion mo ung router. lalabas dun un countdown. bago matapos press a key.

gamitin mo ung 22.03 rc instead of snapshot You do not have permission to view the full content of this post. Log in or register now.
panget gumamit ng snapshot pag di mo alam ginagawa mo.

how po sir diko alam kung pano binili ko lang to para ibypass yun data e diko rin magamit

MF286RA openwrt.

Forum Veteran

Forum Veteran

Addict

Grasshopper

Forum Guru

Honorary Poster

Honorary Poster

Attachments

Forum Veteran

Honorary Poster

Honorary Poster

Grasshopper

Forum Guru

Grasshopper

Forum Guru

Forum Veteran

Grasshopper

Forum Guru

Forum Veteran

Attachments

Grasshopper

Forum Veteran

Similar threads

Popular Tags

About this Thread

Online statistics