Help PLDT HG8145V5 as repeater and HG8145X6-10 as main. paano po?

[PHC- Mr Bean]

Nag search ako sa YøùTùbé and di ko ma gets masyado steps. Is it possible po ba na gamitin yung old router ng PLDT Fibr HG8145V5 as repeater?
Ano po mga gagawin?

Tried

• Disable DCHP (tried but baka may kulang ako na off)
• Connect LAN Cable (main to second)

baka may makatulong po jan. Thank you po ng marami

 

[🤖]

Yes, it is indeed possible to use the PLDT Fibr HG8145V5 as a repeater. Here are the steps you can follow to set it up properly:

1. Set the HG8145V5 to Repeater Mode:
- Access the router's web interface by typing its IP address (usually 192.168.1.1) in your browser.
- Log in using the default username and password. If you haven't changed them, the default credentials are usually "admin" for both.
- Look for the "Repeater" or "Bridge" mode setting in the router's configuration page and enable it.

2. Connect the HG8145V5 to the Main Router (HG8145X6-10):
- Use an Ethernet cable to connect one of the LAN ports of the main router to one of the LAN ports of the HG8145V5 set to repeater mode.

3. Configure LAN Settings:
- Ensure that DHCP is disabled on the HG8145V5 to avoid IP conflicts with the main router.
- Set a static IP address for the HG8145V5 within the same subnet as the main router but outside its DHCP range.

4. Wireless Settings:
- Set the wireless SSID and password of the HG8145V5 to match that of the main router. This will allow devices to seamlessly roam between the two access points.

5. Placement:
- Position the HG8145V5 in a location where it can receive a strong signal from the main router and provide adequate coverage to the areas that need it.

By following these steps, you should be able to effectively use the PLDT Fibr HG8145V5 as a repeater to extend your Wi-Fi coverage. If you encounter any issues or need further clarification on any of the steps, feel free to ask for assistance. Good luck!

 

[PHC- Mr Bean]

Yes, it is indeed possible to use the PLDT Fibr HG8145V5 as a repeater. Here are the steps you can follow to set it up properly:

1. Set the HG8145V5 to Repeater Mode:
- Access the router's web interface by typing its IP address (usually 192.168.1.1) in your browser.
- Log in using the default username and password. If you haven't changed them, the default credentials are usually "admin" for both.
- Look for the "Repeater" or "Bridge" mode setting in the router's configuration page and enable it.

2. Connect the HG8145V5 to the Main Router (HG8145X6-10):
- Use an Ethernet cable to connect one of the LAN ports of the main router to one of the LAN ports of the HG8145V5 set to repeater mode.

3. Configure LAN Settings:
- Ensure that DHCP is disabled on the HG8145V5 to avoid IP conflicts with the main router.
- Set a static IP address for the HG8145V5 within the same subnet as the main router but outside its DHCP range.

4. Wireless Settings:
- Set the wireless SSID and password of the HG8145V5 to match that of the main router. This will allow devices to seamlessly roam between the two access points.

5. Placement:
- Position the HG8145V5 in a location where it can receive a strong signal from the main router and provide adequate coverage to the areas that need it.

By following these steps, you should be able to effectively use the PLDT Fibr HG8145V5 as a repeater to extend your Wi-Fi coverage. If you encounter any issues or need further clarification on any of the steps, feel free to ask for assistance. Good luck!

how to i disable DHCP in HG8145V5 ?

 

[🤖]

how to i disable DHCP in HG8145V5 ?

To disable DHCP on the PLDT Fibr HG8145V5 router, you can follow these steps:

1. Access the router's web interface by typing its IP address in a web browser. The default IP address for the HG8145V5 is usually 192.168.1.1. You may need to log in with the router's username and password. If you haven't changed them, the default credentials are typically "admin" for both.

2. Once logged in, look for the DHCP settings in the router's configuration page. This setting is usually found under the LAN or Network settings.

3. Find the DHCP Server option and disable it. This action will turn off the DHCP server function on the HG8145V5 router.

4. Save your changes and apply the settings. The router may need to reboot for the changes to take effect.

By following these steps, you should be able to successfully disable DHCP on the PLDT Fibr HG8145V5 router. This will prevent IP conflicts when using the router as a repeater in your network setup. If you encounter any difficulties or need further assistance, feel free to ask for help.

 

[Pscdmj]

Set mo as bridge yung nasa wan nung 5v5. Dapat din naka-default or debranded na ang system. Pag kasi naka-pldt pa ang webui, baka kulang-kulang mga settings