fender1991
Enthusiast
sa mga gusto lagyan ng female usb socket . ganito gawin nyo. kuha kayo sa mga sirang power bank pwede un
Attachments
-
You do not have permission to view the full content of this post. Log in or register now.
Yes tested ko na openline b310as kotested na ito mga sir ?
SIR thank you sa TUT. hehe openline na sakin.. na brick man kanina same lang pag unbrick ng 936..
ayun nadale din,.. openline is love
Hindi lang openline..lumakas pa yung signal nya kahit naka sun sim na akoSIR thank you sa TUT. hehe openline na sakin.. na brick man kanina same lang pag unbrick ng 936..
ayun nadale din,.. openline is love
hinde pa po eh. kasi kapag 192.168.254.254. na uunlock sya pero once ma restart or turnoff nabalik sya sa pagka lock.natry mo na palitan dhcp sa configuration ng r01: yung 192.168.254.254 to 192.168.1.1, baka sakaling gumana
yan na ba yong tut?SIR thank you sa TUT. hehe openline na sakin.. na brick man kanina same lang pag unbrick ng 936..
ayun nadale din,.. openline is love
Paps, na stuck ako sa fw unlocker, pwede pa see ng YøùTùbé tut, broken kasi yung linkYes tested ko na openline b310as ko
Exit mo lang tapos balik ka sa balong install erPaps, na stuck ako sa fw unlocker, pwede pa see ng yôutubê tut, broken kasi yung link
Jumper ka ulitExit mo lang tapos balik ka sa balong install er
!!!!UPDATED!!!!
Primary things to do
1. You should know how to solder
2. Get a working USB
3. Download the file using the link
4. Check the USB.jpg and solder the corresponding colors to the solder points
5. Install Necessary drivers and all
Next Step
1. Plug the USB cable with soldered points on the logical board
2. Plug the power cable on the back of your router
3. Put a small wire (tweezers or any conductive material on 2 test points given on USB.jpg) on Jumper test points.
4. Keep the 2 test points shorted with the said material and plug the adapter to the wall outlet.
5. Assuming that all drivers are installed, open the Balong USB Download mode folder and select Balong USB mode flasher.exe
6. Wait for the device to lit the power light
7. Check if the device has been detected (Device manager)
8. Run Unlock FW.exe and wait for it to finish
9. Plug an ethernet cable and launch Network lock remover + USB Download mode.exe (Follow the prompts).
Note: the Network lock remover + USB Download mode.exe has also the option to enter the USB Download mode of your device
so you wont have to bother on unplugging the device and putting a jumper pin again to enter the USB Download mode.
It means that after running the network unlocker and you followed the prompts correctly, the device is READY TO FLASH THE
"Balong USB mode flasher.exe" w/out performing the JUMPER METHOD.
10. Launch Balong USB mode flasher.exe and once the device entered the USB Mode
11. Launch the Firmware Update_11.326. MOD.exe and wait until it finish.
12. Plug in the ethernet if you have unplugged it previously and try to log in to the GUI
13. Check your "Device information" if you have a valid IMEI. If values are all 15 "0", Open IMEI Changer and run IMEI Changer.exe
14. Follow the prompts and type in your Original IMEI and apply it. Wait for it to reboot and you are done
Download link: You do not have permission to view the full content of this post. Log in or register now.
Disclaimer:
I am not held liable for any damaged device during or while performing the steps given in the instructions nor i take credits to the files included in this package.
Please donate to the following to keep them interrested on unlocking, producing files, brainstorming, and contributing to the forums for future devices that will be manufactured with network locks in the the future.
The FF: people are
Zander Mazda
Jerome Laliag
Anonymous Friend
Anonymous device owner
Anonymous Technician
Please find the and donate to the 2 people who made this possible. Dont be just a leecher, any amount will be appreciated by those people.
If you are to be part of a forum, make sure that you are willing to SHARE your ideas and hard-work and expecting a TINY nor even barely nothing in RETURN for it. It is DUE to "You do what makes you happy not what makes you money". It is the true meaning of SHARING and Forum. Let's give KUDOS and Donate to those great folks
Please see Photos for solder points and finished product
FYI: Kahit kaka deliver lng nian Butane soldering torch ko galing pa Amazon. WALA PO AKONG BAYAD na siningil sa nagpa unlock na kakilala lang ng kapit bahay ko. Tapus ikaw maniningil ka ng 500 timawa ka. Mahiya ka naman....
Video Link: You do not have permission to view the full content of this post. Log in or register now.
di mo na kailangang i-run imei changer kung tama naman ang nakalagay na IMEI mo.Guys. Yung natapos yung Firmware Update + IMEI Change. nung inopen ko naging 192.168.8.1 instead of 192.168.254.254. At saka pina.configure ulit yung WIFI from SSID to Password (Quick Set-up). Pero dyan nalang cya paulit-ulit sa Quick Set-up. Any idea paano ito mga bossing.
di mo na kailangang i-run imei changer kung tama naman ang nakalagay na IMEI mo.